| 3. Use Condition |
| Ambient temperature | -25 +85 | |
| Applicable Wire Sizes | AWG #2228 | |
| Applicable PC board thickness | 1.6mm | |
| 4. Appearance and Dimension |
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, or peeling. | |
| Dimension | According to drawings | |
| Exchangeable | Exchangeable with same specification products. | |
| 5. Material |
| Terminal Contact | Brass, 0.64mm thick, Tin plating: 2.55 m, Color: Nature | |
| Housing | Nylon66 UL94V-O, Color: White | |
| Wafer (Straight Pin) | Brass, 0.64mm thick, Tin plating: 24 m, Color: Nature | |
| Wafer (Right Angle Pin) | Phosphor bronze, 0.2mm thick, Tin plating: 2.55 m, Color: Nature | |
| 6. Electrical Performance |
| Rated Current | 3A AC/DC | |
| Rated Voltage | 250V AC/DC | |
| Withstand voltage | No breakdown or flashover | Apply 1000V AC(rms) for 1 minute between adjacent contacts and ground. Leakage current must be less than 0.5mA. |
| Contact Resistance | Initial value 20 | Apply a maximum voltage of 20mV and a maximum current of 100mA to the mated connector. Does not include wire resistance. |
| Insulation Resistance | 1000 M | Apply 500V DC(rms) for 1 minute between adjacent contacts to measure insulation resistance. |
| 7. Mechanical Performance |
| Terminal crimping wire strength | AWG#22: 50N; AWG#24: 30N; AWG#26: 20N; AWG#28: 13N | Axial pullout force at a rate of 253mm per minute. |
| Single contact withdrawal force | 1N | Pullout force test at a rate of 253mm per minute. |
| Terminal and hole seat fixing force | 15N | Force required to pull the terminal out of the hole seat in the wire direction at a rate of 253mm per minute. |
| Single contact insertion force | 5.5N | Insertion force test at a rate of 253mm per minute. |
| Pin Retention Force | 15N | Force required to pull the pin out of the seat at a rate of 253mm per minute. |
| Durability | Contact Resistance 40m; Appearance: No damage | Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test. |
| Vibration | Current Discontinuity: 1 sec; Contact Resistance 40m; Appearance: No damage | Amplitude: 1.5mm p-p; Directions: X, Y, Z axes; Frequency: 10-55-10 Hz/minute; Period: 2 hours for each direction. |
| 8. Environmental Performance |
| Thermal Aging | Contact Resistance 40m; Appearance: No damage | Temperature: 852; Period: 96 hours continuously. |
| Temperature Rise | Measure temperature rise of contact when maximum rated current is passed. | |
| Humidity (Constant) | Contact Resistance 40m; Insulation Resistance 1000M; Appearance: No damage | Temperature: 402; Relative humidity: 90-95% (RH); Period: 96 hours continuously. |
| Temperature Cycling | No breakdown or flashover | One cycle: -553C for 30min, 10-15min transition, then 853C for 30min, 10-15min transition. Total cycles: 5. |
| Salt Spray | Contact Resistance 40m; Appearance: No damage | Temperature: 353; Concentration: 51%; Period: 24H. Test samples are rinsed with clean water and dried naturally after the test. |
| Solder Ability | Soldering area: 90 % | Solder temperature: 2455C; Immersion period: 30.5S. |
| Resistance to Soldering Heat (Wave) | Appearance: No damage | Soldering temperature: 2605; Soldering time: 50.5S. |
| Resistance to Soldering Heat (Manual) | Appearance: No damage | Soldering temperature: 3505; Soldering time: 30.5S. |
