| 3. Use Condition |
| Ambient temperature | -25 +85 | |
| Applicable Wire Sizes | AWG #2632 | |
| Applicable PC board thickness | 0.6l.2mm | |
| 4. Appearance and Dimension |
| Appearance | Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, or peeling. | |
| Dimension | According to drawings | |
| Exchangeable | Exchangeable with same specification products. | |
| 5. Material |
| Terminal Contact | Brass (0.50mm thick), Tin plating: 24 m | |
| Housing Plastic | Nylon UL94V-O(2), Color: Nature | |
| Wafer (A) | Brass (0.50mm thick), Tin plating: 24 m | |
| Wafer (AW) | Nylon UL94V-O(2), Color: Nature | |
| Wafer (PLT) | Nylon UL94V-O(2), Color: White | |
| Wafer (PWT) | LCP UL94V-O, Color: Nature | |
| Contact | Phosphor bronze (0.2mm thick), Tin plating: 24 m | |
| 6. Electrical Performance |
| Rated Voltage | 50V AC DC | |
| Rated Current | 1A AC DC | |
| Withstand voltage | No breakdown or flashover | Apply 500V AC(rms) for 1 minute between adjacent contacts |
| Insulation Resistance | 500 M | Apply 500V DC(rms) for 1 minute between adjacent contacts |
| Contact Resistance | Initial value 20m | Apply 20mV max voltage and 100mA max current to mate connector |
| 7. Mechanical Performance |
| Terminal crimping Wire strength | 20N (AWG#26), 8N (AWG#28), 6N (AWG#30), 0.5N (AWG#32) | Axial pullout force at 253mm/min |
| Fixed terminals And hole seat | 10N | |
| Single contact insertion force | 3N | Housing with terminal ends mated with wafer at 253mm/min |
| Single contact Withdrawal force | 10N | Housing with terminal ends mated with wafer at 253mm/min |
| Pin Retention Force | 13N | Force applied to pin end at 253mm/min until needle exits seat |
| Durability | Contact Resistance 40m ; Appearance: No damage | Mate connectors up 30 cycles at 10 cycles/min before environmental test |
| Vibration | Current Interruption: Max 1 sec; Contact Resistance 40m ; Appearance: No damage | Amplitude: 1.5mm p-p; Frequency: 10-55-10 Hz/min; Period: 2 hours per direction (X, Y, Z axes) |
| 8. Endurance Characteristics |
| Thermal Aging | Contact Resistance 40m ; Appearance: No damage | Temperature: 852; Period: 96 hours continuously |
| Temperature Rise | Measure temperature rise of contact when maximum rated current is passed | |
| Humidity | Contact Resistance 40m ; Insulation Resistance 500m ; Appearance: No damage | Temperature: 402; Relative humidity: 90-95% RH; Period: 96 hours continuously |
| Temperature Cycling | Contact Resistance 40m ; Withstand voltage: No breakdown or flashover; Appearance: No damage | One cycle: -553 (30min) -> 10-15min transition -> 853 (30min) -> 10-15min transition; Total cycles: 5 |
| Solder ability | Solder Area: 90 % | Solder temperature: 2455; Immersion period: 30.5S |
| Salt spray | Contact Resistance 40m ; Appearance: No damage | Solution: 51% NaCl; Temperature: 353; Period: Stamping after tin plated for 8 hours OR Stamping before tin plated for 48 hours |
